Learn · Decorative concrete
GFRC concrete tables and countertops: how they’re made, and how to grind and polish them
If you cast decorative concrete tables or countertops, you have probably come across GFRC — glass-fiber-reinforced concrete. This guide explains what it is, how the usual two-layer casting process works, and how to grind and polish a thin GFRC piece with a planetary machine without cutting through the face coat.
What GFRC is
GFRC is ordinary cement-based concrete made much more useful for furniture and countertops by adding alkali-resistant glass fibers — usually called AR glass fibers — to the mix. The fibers take the place of a steel mesh or rebar cage. They do not rust, so they will not stain the surface the way corroding steel can, and they let you cast thin, strong sections in shapes that would be awkward or heavy in conventional reinforced concrete.[1][4]
For tables and countertops, a typical finished thickness is about 3/4 inch to 1 inch. That is enough for a long, flat top that can be handled and transported, and it is a large part of why GFRC pieces are so much lighter than a conventional precast slab. The Concrete Countertop Institute puts a 3/4 inch GFRC top at about 8 pounds per square foot, compared with about 18 pounds per square foot for a typical 1-1/2 inch steel-reinforced precast top — roughly half the weight, because the GFRC piece can be about half as thick.[1][2]
Conventional precast with mesh or rebar is still used, especially where a thicker, heavier look is wanted. It is a simpler pour, but the slab usually has to be thicker to make room for the steel and to carry the load, so the piece is heavier and less forgiving of complex shapes. For most decorative tables and countertops being made today, GFRC is the usual choice.
How a GFRC piece is built
The common method is a two-layer process.[3][1]
- Face coat or mist coat. This is the layer you will actually see and polish. A mist coat is a thin, fiber-free skin — typically about 1/8 inch. A face coat is a little thicker, sometimes around 1/4 inch, when it carries decorative aggregate. Pigment lives here, and so does any exposed-aggregate or terrazzo look you are planning.
- Backer coat. Once the face has set just enough to stay put, a structural coat with the AR glass fibers is packed, rolled or sprayed on behind it. This is the layer that gives the piece its flexural strength. The backer usually makes up most of the 3/4 inch to 1 inch finished thickness.
Some shops also use a premix or “direct-cast” method, folding the fibers into the whole pour. The risk is fibers showing on the finished face. The two-layer method keeps fibers out of the visible surface — which is exactly why you have to be careful later, when you grind, not to cut through the face coat and into the backer.
GFRC with a polymer modifier often has high early strength and can be demolded in about a day.[2][4] Demolding is not the same as being ready for aggressive grinding. Let the piece gain strength first; polishing a still-green surface can leave a softer, less consistent finish.
Support the piece before you grind
A 3/4 inch GFRC top is strong in flex for its weight, but it is still a thin shell. Before you put a polisher on it, set the piece on a flat, rigid table so the whole underside is supported. If it sags between sawhorses or teeters on a couple of blocks, the machine can dish the surface, break a corner or crack an edge. Support comes first, before you pick a grit.
Protect the face coat
The face coat is thin. That is the single most important thing to remember when you grind GFRC. A very coarse disc — the kind you might reach for to flatten a thick, conventional slab or to bury deep scratches — can cut through the mist coat and expose the fibers in the backer. Once those fibers are visible, they are difficult to hide.
If you want a smooth honed or lightly polished look, start conservatively. Many fabricators begin around 100 or 200 grit on this kind of work, not at the coarsest grinding grit, and they watch the surface after the first few passes. If you do want to expose decorative aggregate, that has to be planned at the pour: the face coat must be thick enough, and you must stop as soon as the aggregate reads consistently. Do not “chase” a thin face coat with a coarser disc.
The DS3011 is a 12" handheld, active-driven planetary polisher with three 5" heads. It will flatten and polish a tabletop efficiently, which is exactly why you should not start coarser than the face coat can spare. For general DS3011 work the machine can be used with lightweight brazed diamond discs and resin polishing pads; on GFRC, choose the starting grit for the thickness of the face, not for maximum stock removal. Need a machine for one project? Rent a DS3011.
Wet process and grit progression
Work wet when you can. Water keeps silica dust down, cools the surface and helps carry away slurry so you can see what the last grit actually did. The DS3011 runs wet or dry and has a center coolant feed; if water is not practical, connect a vacuum and collect the dust.
Then move through the grits in order. A typical progression on a decorative table or countertop — this is common shop practice, not a DS3011 specification — looks like this:
- A moderate starting grit (often 100 or 200) to level the face and take off cement skin, without cutting through it.
- 400 grit, to remove the previous scratch pattern.
- A concrete densifier, then time for it to work, if you are using one (see below).
- 800, then 1,500, then 3,000 if you want a higher polish. Stop earlier for a honed or satin look.
Do not skip grits. The scratches you leave behind only get polished over, not erased, and they show up later in raking light. Let each grit fully remove the pattern of the one before it before you move on.
Densifier, raking light and edges
A silicate densifier is a common step in polished concrete. It hardens and tightens the surface so later, finer pads can develop a more durable sheen. It is especially useful on a cement-rich GFRC face. Follow the product you are using; this is not a substitute for that label.
Check your work with raking side light — a low, glancing light across the surface. Overhead light hides scratches and waves that a window or a raking work light will show immediately. Look between grits, not only at the end.
The flat field of a table or countertop is what a planetary machine does best. Edges, tight corners and returns are usually better finished with a small hand polisher. Running the big machine over an unsupported edge is a common way to chip a crisp arris or round it more than you meant to.
Seal and protect the surface
After polishing, protect the piece. GFRC is still a cement surface, and it remains somewhat porous. Most fabricators use a penetrating sealer, often with a finish coat suited to how the top will be used — including a food-safe system if the table or counter will see dining or food prep. Choose a system that matches the mix and the finish; when in doubt, ask.
A beeswax polish is not a substitute for a sealer, but it is a simple way to enrich an already polished concrete or stone surface. Star Wax Beeswax Polish is made for polished concrete and stone: it adds depth of color and sheen and is easy to renew. For how to apply it, see Beeswax polish for concrete and stone.
For examples of the DS3011 used on concrete tables and similar pieces, see our tools at work. The decorative inlays shown there are Concretely LLC’s own patented process (U.S. patent 12,330,997), not a feature of the machine or a process this article is teaching.
Polish GFRC with a planetary machine
The DS3011 is a 12" handheld planetary polisher for flat concrete and stone work, including tables and countertops.
Sources
- Girard, J., P.E. The Concrete Countertop Institute. “A Complete Guide to GFRC: Glass Fiber Reinforced Concrete for Stronger, Lighter Surfaces.” https://concretecountertopinstitute.com/free-training/complete-guide-to-gfrc-glass-fiber-reinforced-concrete/
- Girard, J., P.E. The Concrete Countertop Institute. “10 Reasons Why GFRC is Better than Precast for Concrete Countertops.” https://concretecountertopinstitute.com/free-training/10-reasons-gfrc-is-better-than-precast/
- The Concrete Countertop Institute. “Concrete Countertop Mix Recipes.” Principles of GFRC mix design: mist/face coat and fibrous backer coat. https://concretecountertopinstitute.com/free-training/concrete-countertop-mix-recipes/
- Driver, C., quoted in Fischer, T. / Concrete Decor. “The Benefits of Glass-fiber Reinforced Concrete.” https://www.concretedecor.net/departments/concrete-countertops/glass-fiber-reinforced-concrete/
Frequently asked questions
What is GFRC?
Glass-fiber-reinforced concrete: a cement-based mix with alkali-resistant (AR) glass fibers instead of a steel mesh or rebar cage. The fibers let fabricators cast thin, light tables and countertops — typically around 3/4 inch to 1 inch — in complex shapes, without steel that can rust and stain.
Why shouldn’t I start with a very coarse grit on GFRC?
The visible face is a thin mist coat or face coat, often about 1/8 inch, or up to about 1/4 inch when it holds decorative aggregate. A very coarse disc can cut through that layer and expose the fibrous backer. Unless you planned to expose aggregate and built a thick enough face coat for that, start conservatively and watch the surface.
Should I grind and polish GFRC wet or dry?
The DS3011 can run wet or dry, but a wet process is usually the better choice on decorative tables and countertops: it keeps dust down, cools the surface, and is gentler on a thin face coat. If water is not practical, use vacuum dust collection.
How should I support a GFRC table or countertop while polishing?
Support the piece on a flat, rigid table so the whole underside is backed up. Thin GFRC can flex. If it sags between supports, you can dish the surface, break a corner or crack an edge.
Can I rent a machine to polish a GFRC piece?
Yes. INTER-TOOL rents the DS3011 from San Leandro, California. It is a 12" handheld planetary polisher well suited to flat tabletops and countertops. Edges are still best finished with a small hand polisher.