Back

Learn · DS3011

Why three rotating heads cut flatter — the DS3011 planetary idea

Three rotating heads take a stable three-point stance — a triangle, the most stable figure. The machine uses two forces: gravity, its own correctly chosen weight, and rotation (RPM). Together they create the right working conditions for diamond tooling, so you do not need to press down. You just guide it.

The DS3011’s three heads sit in a triangle. The carrier turns one way; each head spins the other — planetary motion. Simplified illustration, slowed down; not to scale.

The short idea

The INTER-TOOL DS3011 is a 12" handheld, active-driven planetary polisher. Under the deck, three 5" diamond discs do the cutting. The carrier plate turns one way around the center while each head spins the other way on its own axis — planetary motion, the same idea as a planet that rotates while it orbits the sun.

Two things matter as much as the motion itself. First, three heads are three contact points: a triangle, the simplest shape that sits flat — unlike a typical single-head grinder, which can be hard to keep level and can leave swirl marks if the head tilts. Second, the machine uses two forces — gravity, its own correctly chosen weight, and rotation (RPM). Together they create the right working conditions for diamond tooling, so you do not need to add pressure. You just guide it.

Three points and a triangle

Three points that are not in a straight line define exactly one plane. That is why a tripod or a three-legged stool will sit on an uneven floor: all three feet can touch at once, and there is only one way for them to do so.[1][2]

A single-head grinder or polisher can be hard to keep flat and level; if the head tilts or dips, swirl marks can follow.[3][4] Three heads arranged in a triangle give a three-point stance. The tool sits down and stays flat — on a slightly uneven slab, a slightly crowned concrete top, or a surface that is still being flattened.

Three heads in a triangle sit flat; a single head can tilt and is hard to keep stable 3 headssit flat A single headcan tilt
Three heads sit flat, like a tripod. A single head can tilt.

A flatter, more even cut

Because the weight of the machine is shared among three pads, no single disc is asked to carry the whole load. A single-head machine can be harder to keep flat over an area, and it can leave a more visible scratch or swirl pattern.[4] Three heads in a triangle stay flat, and their overlapping paths keep changing direction, which is why a planetary pattern is used for a flatter, more even finish — and why the DS3011 is described as five times faster than a single-head machine for this kind of work, with more even diamond wear.

That is a geometric advantage, not a promise that any surface will come out perfectly flat on its own. You still guide the machine, keep it moving, and work through the grits. The three-point stance simply gives the cut a more stable starting point.

Three heads cutting an even, flat line, versus a single head that tilts and leaves swirl marks Even,flat cut A single headcan leave swirls
Three heads stay flat and even; a single head can leave swirl marks.

Gravity and RPM

The machine uses two forces: gravity — its own, correctly chosen weight — and rotation (RPM). Together they create the right working conditions for diamond tooling, so no extra pressure is needed. You just guide the machine.

That has been proved by time. The concept has been on the market for nearly 20 years, through a great deal of research and development. Competitors appeared and disappeared; the DS3011’s concept survived, and it still works.

A downward gravity arrow and a rotation arrow: the two forces that let the machine work without added pressure Gravity RPM No extra pressure —just guide it
Gravity and RPM, in the right proportion, do the work. You just guide the machine.
A small spur gear turning a much larger spur gear, with the teeth meshing Small gear turnsthe large one
A small gear turns a large one.

Prepare an uneven surface

If the surface is uneven, first take off protruding objects, metal pieces and high edges (ledges) with a grinder. After that, the DS3011 does the rest of the work.

An uneven surface with ledges being ground first, then a flat surface ready for the three-head DS3011 Grind ledgesand metal first Then theDS3011
Grind off ledges, metal and high spots first; then the DS3011 does the rest.

For stone shops and restoration

Stone shops typically polish by hand with single-head grinders, and many higher-volume shops also use large automatic machines such as edge or line polishers.[5] Those automatic machines are a major purchase — often tens or hundreds of thousands of dollars — so not every shop has one.[5] When a machine does go down, parts and specialized service can take days or longer to arrive, and the shop may sit idle while it waits.[6]

For restoring large slabs, kitchen countertops and other stone tables or surfaces, the DS3011 is a practical tool for restoration and polishing. It can even polish metal surfaces.

Counter-rotation and control

There is a related point about control. On the DS3011 the heads spin the opposite way from the carrier. Any rotating pad pushes back on the machine — that is simply reaction torque. When the heads counter-rotate relative to the carrier, those reaction forces are at least partly set against each other rather than all adding up in one direction. The tool is easier to keep under control than a single large disc that wants to walk or twist in one direction the whole time.

This is a general mechanics point, not a claim that the machine is perfectly balanced in the hand. Counter-rotation is one reason a planetary layout feels calmer to run than it looks on paper.

The carrier plate turning one way while the three heads spin the opposite way, partly balancing reaction forces Carrier one way,heads the other
The carrier turns one way; the heads spin the other.

See it move

The planetary motion section on the DS3011 page has a short animation of the carrier and the three heads, and a video of planetary polishing in action: Watch how planetary polishing works.

The DS3011 is a 12" handheld machine, proudly made in the USA in California, and used on polished concrete countertops, benches and fire pits, and on marble, granite and terrazzo. Need one for a single project? Rent a DS3011 from INTER-TOOL in San Leandro.

DS3011 · 12" handheld planetary polisher

Three 5" heads and a 12" grinding width — built for concrete and stone.

Sources

  1. Boyd, A. University of Houston, The Engines of Our Ingenuity, episode 2533. “The Power of Three.” https://engines.egr.uh.edu/episode/2533
  2. University of Regina, Math Central. “A three legged stool.” https://mathcentral.uregina.ca/qq/database/qq.09.00/teri1.html
  3. Bertram, N. Concrete Decor. “Concrete Countertop Polishing Tips and Tricks.” https://www.concretedecor.net/departments/tools-and-equipment/concrete-countertop-polishing/
  4. Diamond Tool Warehouse. “Single Disc vs Planetary Head Concrete Grinders: Which One Should You Buy?” https://diamondtoolwarehouse.com.au/single-disc-vs-planetary-head-concrete-grinders-which-one-should-you-buy/
  5. SlabWise Editorial Team (May 25, 2026). “Stone Polishing Equipment: What Stone Shops Actually Use.” https://slabwise.com/guide/stone-polishing-equipment
  6. Crown Stone USA (April 21, 2026). “How to Choose the Right Edge Polisher for Your Granite and Quartz Shop.” https://crownstoneusa.com/feeds/blog/edge-polisher-stone

Frequently asked questions

Why do three heads stay flatter than a typical single-head grinder?

A single-head grinder or polisher can be hard to keep flat and level; if the head tilts or dips, swirl or scratch marks can follow. Three heads arranged in a triangle give a three-point stance, like a tripod, so the machine sits down and stays flat.

Do I need to press down on the DS3011?

No. The machine uses two forces: gravity — its own, correctly chosen weight — and rotation (RPM). Together they create the right working conditions for diamond tooling, so no extra pressure is needed. You just guide it.

What if the surface is uneven?

First remove protruding objects, metal pieces and high edges (ledges) with a grinder. After that, the DS3011 does the rest of the work.

What is planetary motion on the DS3011?

The carrier plate turns one way around the center while each of the three pad heads spins the opposite way on its own axis. The overlapping paths wear the diamonds more evenly and help produce a virtually swirl-free finish. See the animation and video on the DS3011 planetary motion section.

Can I rent a DS3011 to try this?

Yes. INTER-TOOL rents the DS3011 from San Leandro, California, by the day, weekend or week, and rental fees can be credited toward a new machine. See Rent a DS3011.